You’ll find the Pelican transom motor mount fits Catch PWR 100, Catch Mode 110 and Getaway 110 kayaks and accepts electric or gas motors up to 2.5 hp, provided you verify shaft length and weight. It’s molded polypropylene reinforced with fiberglass for light, stiff, corrosion-resistant service and bolts to factory reinforcement points using a five-bolt pattern. Installation is straightforward but check hole alignment and torque, and be aware long-term UV and storage can affect plastics—more specifics follow.
Some Key Takeaways
- Designed for Pelican Catch/Getaway kayaks, the mount supports electric or gas motors up to 2.5 hp when paired with compatible transoms.
- Reinforced fiberglass-polypropylene construction is lightweight (≈1.5 lb) and corrosion-resistant, suitable for saltwater use.
- Five-bolt pattern and broad force distribution reduce hull flex and improve straight-line tracking and thrust alignment.
- Installation requires drilling at factory reinforcement points, cross-tightening bolts, and verifying vertical alignment before launching.
- Limitations: restricted to specific hull models, basic hardware may need upgrades, and prolonged sun storage can stiffen the plastic.
Which Kayaks and Motors Is the Pelican Transom Motor Mount Compatible With?
The Pelican Transom Motor Mount is built specifically for Pelican’s Catch series kayaks—Catch PWR 100 (MF10), Catch Mode 110 (MI11), and Getaway 110 (MH10)—and lets you attach electric or gas motors up to 2.5 hp for reliable trolling performance. You’ll find the mount matches those kayak models’ transom geometry and load limits. It supports common motor types used for small craft: low-power outboards and compact electric trolling motors. Materials and hardware resist flex under thrust, so you’ll maintain alignment and steering control. Check your motor’s shaft length and weight to confirm compatibility before pairing for safe operation. Wilderness Systems offers a range of kayaks and accessories for paddlers seeking durable, adventure-ready equipment, including models optimized for water adventures.
How to Install the Pelican Transom Mount on Catch and Getaway Kayaks
Before you start, lay out the mount, hardware, and tools and confirm your kayak model (Catch PWR 100, Catch Mode 110, or Getaway 110) and motor specs so you’re sure the mount and motor fall within the 2.5 hp and transom load limits. Position the mount on the transom, align the bolt pattern with factory reinforcement points, and mark drill locations. Drill with appropriate size, deburr holes, then fit bolts with washers and nuts. Tighten using the recommended torque sequence: snug in a cross pattern, then final torque to spec. Verify vertical alignment and test securely before launching. Gear up with quality Lifetime kayaks and accessories for safe, reliable kayak adventures.
Build Quality and Materials: Durability of the Polypropylene + Fiberglass Mount
When you rely on a transom mount for propulsion, polypropylene reinforced with fiberglass gives a strong, corrosion-resistant backbone that won’t rot or pit like metal in saltwater environments. You’ll find the PS1900-00 light (1.5 lb) yet stiff, resisting flex under static motor loads. The fiber content boosts impact resistance and distributes clamping stress across the mount, reducing stress risers at bolt holes. UV stability is good for seasonal exposure, though long-term sun-baking will slowly degrade polymers; store covered when not in use. Hardware quality and proper torque matter—use supplied bolts, washers, and nuts to preserve fit and longevity. Power Pole Essentials for Kayak Water Adventures offers a range of compatible mounts and accessories for paddlers looking to upgrade their setup, including guidance on kayaks and power poles.
Real-World Performance: Stability, Motor Fit, and Handling With Up to 2.5 HP
Although it’s modestly sized and light, you’ll find the PS1900-00 holds a motor up to 2.5 hp with reassuring stability when mounted correctly on compatible Catch/Getaway hulls. You’ll notice clean thrust alignment reduces yaw, so straight-line tracking improves without added steering load. Propulsion efficiency stays acceptable for short runs and trolling, provided the motor shaft clears the transom cutout and you tighten the five-bolt pattern. Hull interaction is predictable; the mount transmits forces to broad hull sections, limiting flex. Expect minimal noise vibration at low RPMs, though higher throttle can introduce chatter—check fasteners and motor tilt to tame it. Designed for paddlers and anglers who value secure gear transport, the mount works well with common kayak tie-down straps used by outdoor enthusiasts.
Should You Buy It? Pros, Cons, and Final Recommendation
The PS1900-00’s reliable mounting and predictable hull interaction make the decision straightforward for owners of compatible Catch/Getaway kayaks: if you need a lightweight, budget-friendly transom mount to run an electric or small gas motor up to 2.5 hp for trolling or short excursions, this unit is a solid choice. Pros: simple installation, reinforced polypropylene resists corrosion, low weight, and compatible hardware. Cons: limited to specific hulls, basic hardware may need upgrades, and long term storage can stiffen plastic without proper support. Consider pricing trends and resale value; sensible user modifications can extend usefulness and improve appeal. Many motor-ready kayak owners appreciate accessories and upgrades tailored for motor-ready fishing kayaks to optimize performance and convenience.
Some Questions Answered
Can This Mount Be Used on Non-Pelican Kayaks?
Yes — you can use it on non-Pelican kayaks if you confirm hull compatibility and fit. You’ll measure transom thickness, curvature, and flat mounting area; the mount bolts through with included hardware. If your kayak’s transom geometry doesn’t match, you’ll need transom adapters or a spacer plate to create a flat, reinforced surface. Always reinforce weak fiberglass or polyethylene surfaces and torque bolts per spec to avoid stress or leaks.
Is Drilling Required for Installation on Older Kayak Models?
No — drilling isn’t strictly required, but many older kayaks need it for a permanent install. You can use drill free alternatives like padded clamps, transom straps, or heavy-duty bracket adapters for temporary mounting that keep hull integrity. Those methods suit short-term tests or rentals, but they’re less secure than bolting. If you plan regular use or heavier motors, you’ll likely want to drill and through-bolt with backing plates for a safe, durable attachment.
Will Saltwater Exposure Cause Accelerated Corrosion or Degradation?
Yes — saltwater corrosion can accelerate degradation if you don’t take precautions. You’ll want to rinse the polypropylene reinforced with fiberglass mount and all stainless hardware after each use, inspect fasteners for pitting, and apply protective coatings like marine-grade anti-corrosion sprays or sacrificial zincs on metal parts. Regular maintenance and drying will extend service life; ignore salt buildup and you’ll see accelerated wear and possible hardware failure.
Are Replacement Bolts or Hardware Available Separately?
Yes — you can get replacement hardware for the mount. You’ll want OEM replacement hardware or aftermarket kits that match the five bolts, five nuts and ten washers specified. Check Pelican’s parts/support or reputable marine suppliers for stainless or corrosion-resistant aftermarket kits if you’ll use saltwater. Measure bolt sizes and thread pitches before buying to verify fit, and keep proof of purchase handy for warranty or exact-match inquiries.
Can I Attach a Fish Finder or Accessory to the Mount?
Yes — you can attach a fish finder or accessory to the mount, but plan placements carefully for accessory compatibility. You’ll need aftermarket brackets or a small plate to secure a transducer and avoid interference with the motor’s clamp. Route wiring for power integration through or alongside the mount, keeping cables clear of moving parts and water exposure. Test alignment and waterproof connections before each trip to guarantee reliable performance.
